Day: March 5, 2006

Tractor deck…

lpaulriddle

I put the deck back on the tractor yesterday, and I’ve got the skinned knuckles to prove it.

Every fall, I take the deck off the tractor. The sole purpose of this is so I can take the blades off to sharpen them. Now, it’s really, really easy to take the deck off the tractor, and it’s really, really hard to put it back on. But, because I take it off at the end of the mowing season, I can wait 4 months to put it back on. Of course, the 4 months go by quickly, and before I know it, I’m out putting the deck on, skinning my knuckles, and cursing up a storm.

My tractor was a freebie that came with the house. I really can’t complain too much about it, because it runs pretty well. It’s a “Powr Kraft”, which is the Montgomery Ward house brand, which should give you an idea of its age. Of course, like every other house brand, it’s built by MTD. My theory is that MTD tractors are made by guys who hate tractor mechanics. There are about 15,000 little lifter arms and cotter pins that attach the deck to the tractor. To put the deck on, you first have to slide it underneath the tractor. Well, while you’re doing this, you have to keep moving the little lifter arms out of the way, because they are always catching on the pulleys, belt, etc. Then, you have to perfectly align the deck with the tractor, and slide this metal rod through both of them. But, it’s hard to do this because the belt is in the way. Etc. etc. etc.

This year, I tried jacking the tractor up, and it did make it easier to slide the deck underneath. But, I couldn’t set the tractor back down on the deck, because the 15,000 little lifter arms kept getting wedged on stuff. Net result: Jacking the tractor doesn’t make it any easier.

One of the reasons I keep putting myself through this, is that I only have to do it once a year. After a year, I tend to forget what a pain it is. Remember the old adage, “Time heals all wounds?”

If I could figure out how to remove the blades with the deck still on the tractor, I wouldn’t have to do this any more. Problem is, I’d have to get underneath the tractor with my impact wrench somehow. That would mean raising the tractor about 2 feet off the ground. Then I’d have to replace the blades from underneath too. Somehow, that sounds like just as much of a pain as removing/replacing the deck. But, it’s worth trying once, if I can figure out how to do it. Maybe this will be the year..

Plumbing project finally completed

lpaulriddle

Well, I wasn’t sure I’d ever see this day, but the basement plumbing project is finally finished. It went smoothly and pretty much according to plan. No more leaky fitting in the basement, and I now have a working frost free sillcock outside by the pool equipment. I started at 8:30am on Friday, and finished up at around 1:30pm, with lunch and a couple of breaks in between. Lessons learned along the way:

  1. I had originally suspected that our house shutoff didn’t fully shut the water off, but it looks like it does after all. It just takes a long time to drain the house plumbing. When I first cut the pipes apart, I had a persistent drizzle coming out of the cut pipe. At the time, I had opened every faucet in the house except for the bar sink. When I opened the bar sink faucet, the drizzle stopped and I was able to sweat the pipe without using any bread.
  2. I tried to solder one of the joints while there was still some standing water in the pipe near the joint. It took a loooong time before the pipe got hot enough to melt the solder. In the process, the heat from the torch boiled the water off. Despite my worries, I still ended up with a leak-free joint. Next time though, I’ll make sure the joint is a dry as possible before soldering. Barring that, make sure there’s an opening somewhere for the steam to escape.
  3. Don’t hold the torch directly below the joint, or solder will drip into it and foul up the torch tip. Fortunately, they’re cheap..

This was the biggest project I’ve ever done involving copper sweating. I’ve found that as long as the joints are fully cleaned and fluxed, it’s pretty hard not to end up with a leak-free joint.

Really glad to finish that one up!